1.0-1.5t/h Twin Screw Fish Feed Extrusion Line | Turnkey Solution
CE Certified
ISO Certified
60+ Countries

1.0-1.5t/h Twin Screw Fish Feed Extrusion Line | Turnkey Solution

<p><strong>Twin Screw Fish Feed Extrusion Line, 1.0–1.5 t/h, 304 Stainless Steel</strong> — engineered for floating and sinking aquaculture feed production across trout, salmon, and catfish species.</p> <ul> <li>Screw configuration and die design specified to raw material formulation and target pellet density</li> <li>Barrel temperature profile tuned for starch gelatinisation, expansion control, and consistent floatation performance</li> <li>In-house trial runs on customer raw material before shipment validate output against buyer specifications</li> </ul> <p>Delivered as a throughput-matched line from extrusion through drying and coating, with documented screw and die configuration records retained for future reorders.</p>

High Efficiency
Customizable
PLC Control
After-Sales Support

Product Description

Screw Profile Matched to Formulation — Trial runs on your specific raw material confirm pellet density and expansion before the line leaves the factory.

Technical Specifications

Parameter Value
Product Type Twin Screw Fish Feed Extrusion Line
Output Capacity 1.0–1.5 t/h (basis not stated in source — confirm raw material formulation, moisture content, and pellet size)
Screw Type Twin-screw
Construction Material (Product Contact) 304 stainless steel
Control System PLC / MCC (to be confirmed based on plant preference)
Voltage & Frequency Configurable to destination market (to be confirmed)
Target Species Trout, salmon, catfish (floating and sinking formats)
Die Configuration Specified to pellet diameter and density target (to be confirmed)
Steam or Water Injection To be confirmed based on preconditioning requirements
Assembly State Complete processing line (scope to be confirmed)

Application Suitability

Application Material or Output
Floating feed for trout and salmon High-protein formulations requiring controlled expansion and starch gelatinisation
Sinking feed for catfish Dense pellet formulations requiring compression over expansion at the die
Multi-species feed milling Lines producing different pellet sizes and densities on the same extruder platform
Marine species grow-out feed Formulations with fish meal and oil content requiring matched drying and coating capacity

Why Pellet Density Drifts When the Screw Profile Is Copied

Extrusion parameters must be dialed to the actual raw material, not transplanted from a generic build.

A floating feed pellet that sinks on arrival destroys credibility with the end farmer. The issue is rarely the extruder itself but the screw configuration and die geometry that were carried over from a different formulation. I have seen lines where a manufacturer swapped to a higher-fat fish meal blend and suddenly half the output dropped below the waterline, because the shear profile and barrel temperature zones were set for a starch-heavy corn base. The twin screw fish feed extrusion line only holds specification when the screw elements, die land length, and moisture preconditioning are all specified against the buyer’s exact recipe. [NEED_CITE: starch gelatinisation temperature ranges in aquaculture feed processing]

Twin screw fish feed extrusion line with barrel, die assembly, and preconditioner

Screw Element Sequencing and Shear Control

The arrangement of conveying, kneading, and reverse-screw elements inside the barrel determines how much mechanical energy transfers into the material. For floating feed, the twin screw fish feed extrusion line needs a longer high-shear section to achieve full starch gelatinisation and trap air pockets during expansion at the die. For sinking feed targeting catfish, the screw profile shifts toward gentler mixing with higher compression, pushing density above the waterline threshold. This is not a matter of swapping one element — the entire sequence from feed inlet to die face must be reconfigured when switching between floating and sinking formats.

Barrel Temperature Zones and Moisture Balance

Each barrel section can be heated or cooled independently, creating a temperature gradient that controls viscosity as the dough moves toward the die. If the mid-barrel zone runs too hot on a high-fat trout formulation, the fat separates before the pellet reaches the die face, producing a crumbly pellet with poor water stability. Getting the barrel profile right requires knowing the fat content, protein source, and starch level of the incoming mix, which is why preconditioner steam injection and barrel zone settings are tuned together rather than in isolation. [NEED_CITE: barrel temperature profiling in twin-screw extrusion for aquatic feed]

How Die Land Length Shapes Pellet Density

The die plate is not just a hole — the length of the land (the straight channel the dough passes through before exiting) directly controls back-pressure and expansion ratio. A short land lets the pellet expand aggressively at exit, locking in buoyancy for floating feed. A longer land holds pressure higher, compressing the pellet into a denser form that sinks. Die diameter, number of holes, and land length are all specified to the target pellet size and species. A trout farm expecting 3mm pellets and a catfish operation needing 6mm sinking pellets require entirely different die plates on the same extruder.

Die plate close-up showing pellet forming channels and cutter assembly

What Happens When Line Stations Are Mismatched

An extruder producing 1.5 tonnes per hour is only productive if the dryer and coating drum can handle that same volume without bottlenecking. I have seen installations where the extruder was specified correctly but the dryer was undersized, forcing the operator to slow the extruder and run at a fraction of capacity just to avoid sending wet pellets to the coater. The twin screw fish feed extrusion line must have throughput matched across every station — mixer, extruder, dryer, coating drum, cooler, and packing — or the rated output is meaningless. Undersized downstream equipment also forces longer residence times in the dryer, which can over-dry the pellet surface while the core retains moisture, leading to cracking and fines generation during storage. [NEED_CITE: throughput matching across aquaculture feed processing stations]

Why This Line Is Built Around Your Recipe

The screw configuration and die geometry are specified to the buyer’s raw material and target pellet density, not pulled from a standard catalogue. The in-house testing workshop runs trial batches on the customer’s actual formulation before shipment, confirming expansion ratio, floatation percentage, and water stability. Throughput is matched across extruder, dryer, and coating stations so no single element bottlenecks the line. Electrical schematics and control language are confirmed to the destination market before production begins, avoiding commissioning delays. Pre-sales engineering covers line layout and utility planning, and support continues through on-site installation, operator training, and wear parts supply.

Documentation & Verification

  • Screw and die configuration record documenting element sequence, die land length, and target pellet density for your formulation
  • Trial run report on your raw material confirming expansion ratio, floatation, and water stability before dispatch
  • Line layout and capacity calculation showing matched throughput across extruder, dryer, and coating stations
  • Electrical schematic with voltage, frequency, and control language confirmed to your facility’s power supply
  • Wear parts list specifying screw elements, die plates, and cutter blades with reorder references

Installation, Commissioning & Support

  • Foundation plan accounts for extruder weight and vibration, with anchor bolt layout provided before concrete pour
  • Dedicated electrical circuit sized for the main drive motor, with voltage and frequency verified to local supply
  • Extruder barrel sections and screw shafts ship disassembled for container loading, with reassembly supervised on site
  • First-run commissioning includes screw speed, barrel temperature, and moisture adjustment to hit pellet density targets
  • Operator training covers screw element inspection, die plate changeover, and daily grease point schedules
  • Wear parts stock list provided at handover, covering high-wear screw elements and die plates for initial production runs

What We Need to Move Forward

To configure the line correctly, we need your raw material formulation including protein source, fat percentage, and starch content, along with the target pellet diameter and whether floating or sinking feed is required. Confirm your facility’s voltage, frequency, and preferred control language so the electrical package matches your site. If you are adding this line to an existing plant, share the capacity of your current mixer and packing station so throughput can be balanced across the full process.

Frequently Asked Questions

Q: How is output capacity verified on the buyer’s actual raw material formulation?
A: We run trial batches in our testing workshop using the customer’s raw material or a close equivalent. The trial measures throughput, pellet density, expansion ratio, and water stability under controlled conditions. Results are documented in a report shared before shipment, so the buyer knows the line holds specification on their formulation rather than on a generic test recipe.

Q: How are screw configuration and die design matched to floating versus sinking feed targets?
A: Floating feed requires a screw profile with higher shear to fully gelatinise starch and trap air for buoyancy, paired with a short-land die for expansion. Sinking feed uses gentler mixing elements and a longer-land die to compress the pellet. Both configurations are documented in the screw and die record for future reorders.

Q: What is the scope of line stations included?
A: The complete line typically covers mixing, extrusion, drying, coating, cooling, and packing. Each station is sized to match the extruder’s throughput so no bottleneck forms downstream. The exact scope is confirmed during the line layout phase based on the buyer’s production requirements and existing equipment.

Q: Is a trial run performed on the buyer’s raw material before shipment?
A: Yes. The in-house testing workshop runs the buyer’s formulation through the extruder before the line ships. The trial confirms pellet density, expansion, and durability against the target specification. If adjustments are needed to the screw profile or die geometry, they are made and retested before factory acceptance.

Q: How are voltage, frequency, and control language confirmed?
A: The buyer provides their facility’s electrical supply details and preferred control interface language during the specification phase. The electrical schematic and PLC program are built to those parameters, avoiding delays during on-site commissioning caused by mismatched power supply or unfamiliar interface language.

15+
Years Experience
60+
Countries Served
1000+
Projects Delivered
24/7
Technical Support
Get a Custom Quote

Interested in 1.0-1.5t/h Twin Screw Fish Feed Extrusion Line | Turnkey Solution?

Fill out the form below and our engineering team will respond within 24 hours with a tailored solution.

Sending your inquiry...

Your information is secure and will only be used to respond to your inquiry.

Explore more equipment from our product range

pet food making machine

Twin Screw Extruder for Floating Sinking Fish Feed – Production Line

<p><strong>Twin Screw Fish Feed Extrusion Production Line, 0.5–12 mm Pellet Range, Floating & Sinking Feed</strong> — engineered for precise density control across aquaculture formulations. Screw configuration and barrel temperature profiling determine whether pellets float or sink, with die design matched to your raw material for consistent expansion and texture. Trial runs on your actual formulation confirm target pellet density before shipment.</p> <ul> <li>Supports continuous operation across fry to grow-out stages</li> <li>Stainless steel contact materials for feed-grade hygiene</li> <li>Line layout and capacity calculation based on your specific formulation, not nominal figures</li> </ul>

View Details
pet food making machine

MT70 Twin Screw Pet Food Extrusion Line | Technical Guide

<p><strong>MT70 Twin Screw Pet Food Extrusion Line, 380V 50Hz, PLC Control</strong> — engineered for precise kibble density and texture through matched screw configuration and die design.</p> <ul> <li>Barrel temperature profile and moisture control ensure consistent starch gelatinisation and expansion across dry kibble, semi-moist and treat recipes.</li> <li>Automated PLC and MCC integration across mixing, extrusion, drying and packaging stations maintains throughput balance.</li> <li>Screw geometry and die specifications are documented against your raw material and target product before production begins.</li> <li>Trial runs on customer-supplied raw materials are completed in our testing workshop, with full reports provided prior to shipment.</li> </ul>

View Details